Design and Development of an IC based RF Receiver

The project is an INTEGRATED CIRCUITS (IC) BASED RADIO FREQUENCY (RF) RECEIVER, which is essentially a superheterodyne receiver that uses frequency mixing to convert a received signal to a fixed intermediate frequency (IF). This signal can then be more conveniently processed than the original carrie

Project Title

Design and Development of an IC based RF Receiver

Project Area of Specialization

Electrical/Electronic Engineering

Project Summary

The project is an INTEGRATED CIRCUITS (IC) BASED RADIO FREQUENCY (RF) RECEIVER, which is essentially a superheterodyne receiver that uses frequency mixing to convert a received signal to a fixed intermediate frequency (IF). This signal can then be more conveniently processed than the original carrier frequency. The receiver is designed for Wireless applications at S-band operating within 2.4-2.5 GHz frequency range. The design consists of a number of RF components which are designed, configured and optimized to produce the required results.

The most important feature of the superheterodyne receiver is its selectivity i.e., the capability to select and process small signals in the presence of strong interferers.

The final product will be the designed receiver system fabricated on a Printed Circuit Board (PCB) which can be incorporated in the signal flow chain (as shown in Figure 1) for signal processing. The receiver system will generate an analog signal at its output which can be converted into other forms as desired.

               Figure 1: Signal Flow Diagram

Project Objectives

• To design a receiver system that receives radio waves and converts the information carried by them to a usable form
• To pursue a design approach for the development of Radio Frequency (RF) receiver system suitable for Wireless applications
• To realize and verify the functional properties of the Radio Frequency (RF) design components

Project Implementation Method

Design Specifications: 

 Block Diagram:

The block diagram shows the receiver architecture. Starting from the antenna, which is used for the reception of radiofrequency, these signals are converted into electric currents which are then processed by the subsequent microwave circuit. 

At the RF chain input, the receiver receives RF frequencies through the antenna which are filtered out by the Band Pass Filter. The filtered frequencies are amplified by the Low Noise Amplifier producing an appropriate signal level that is down converted by the mixer.

The Voltage Controlled Oscillator provides a stable local oscillator (LO) frequency for frequency down conversion at the mixer LO port. The mixer performs the actual down conversion to produce an intermediate frequency (IF) at its output port.

The IF signal is filtered by the Low Pass Filter in the IF chain to get rid of the high frequencies and harmonics. This signal is then amplified to produce a reasonable output.   

Specification

Operating Frequency Range (Receiver)

RF Centre Frequency

RF Bandwidth

IF Cutoff Frequency

LO Frequency

Patch Antenna (operating frequency)

                        Figure 2: Block Diagram

Benefits of the Project

• Superheterodyne receiver prevents image noise fold over due to use of two IF frequencies before conversion to baseband.
• As it converts high frequency to low frequency, all processing takes place at lower frequencies. The devices are cheaper at such lower frequencies compared to higher frequencies.
• It is easy to filter IF signal compared to RF signal.
• It offers better sensitivity in contrast to homodyne receiver architecture.

Technical Details of Final Deliverable

 

 The final design of the receiver can be seen in Fig.3. The design has been established after the design and exploration of the RF components and their variants at the system level, followed by the co-simulation and configuration of the individual components and concluded with the co-simulation and verification of the entire system, taking into account parasitic interconnections and substrate effects.

Individual Components:

 The receiver antenna is a Patch Antenna (as shown in Fig.4) which has been designed using the inset feed topology for operation in the desired frequency band i.e., 2.4-2.5 GHz.

The Band Pass Filter (as shown in Fig. 5) is designed using Microstrip Coupled Lines which filters out the received radio signals to obtain the frequencies in the desired frequency band.

The Low Pass Filter (as shown in Fig. 6) is designed using Lumped Components which filters out the frequencies generated at the output port of the mixer to obtain an intermediate frequency which is lower than the received radio frequency and can be easily processed.

The Low Noise Amplifier (Fig.7) is the SAV-541+ which is a high IP3 transistor device, manufactured using E-PHEMT technology enabling it to work with a single positive supply voltage. It has outstanding Noise Figure, particularly below 2.5 GHz.

The Power Amplifier (Fig.8) is the PGA-105+ which is an advanced ultra-flat gain amplifier fabricated using E-PHEMT technology and offers extremely high dynamic range over a broad frequency range and with low noise figure. In addition, the PGA-105+ has good input and output return loss over a broad frequency range without the need for external matching components.

The Frequency Mixer (Fig.9) is the MCA-35 MH+ which is a non-linear three port device that performs the frequency mixing of the two signals applied at its input ports.

The Voltage Controlled Oscillator (Fig.10) is the ROS-3050-819+ which produces a periodic AC signal whose oscillation frequency is determined by its input voltage.

 Figure 3: Complete structural design of the receiver

             Figure 4: Design of receiver antenna

                    Figure 5: Band Pass Filter

                    Figure 6: Low Pass Filter

         Figure 7: Low Noise Amplifier (SAV-541+)

            Figure 8: Power Amplifier (PGA-105+)

                  Figure 9: Mixer (MCA-35 MH+)

Figure 10: Voltage Controlled Oscillator (ROS-3050-819+)

                  Figure 11: Attenuator (PAT-3+)

Final Deliverable of the Project

Hardware System

Core Industry

Telecommunication

Other Industries

Core Technology

Others

Other Technologies

Sustainable Development Goals

Industry, Innovation and Infrastructure, Sustainable Cities and Communities

Required Resources

If you need this project, please contact me on contact@adikhanofficial.com