electric bike
This government takes the safety of pedestrians and cyclists very seriously. The Ministry has undertaken many initiatives to improve the safety of vulnerable road users ? mandatory bicycle helmets for children, stricter driver licensing for moped users, higher fines for failing to yield to ped
2025-06-28 16:32:20 - Adil Khan
electric bike
Project Area of Specialization Electrical/Electronic EngineeringProject Summary- E-bikes are silent (conventional bicycles generate noise from pedalling and chains);
- Ease with which maximum motor speed can be increased through modifications;
- Absence of standards/requirements for e-bike electrical components;
- View that e-bikes can be operated by those with suspended licences to circumvent impaired driving penalties;
- Sharing roads and bicycle paths with pedestrians and cyclists, given that some e-bikes are wider, longer and heavier than regular bicycles;
- Inadequate braking systems, particularly those found on the larger/heavier e-bikes;
- E-bikes resembling scooters cause confusion as to where they fit within the regulatory scheme on the part of law enforcement, municipalities and the general public;
- No requirement for licensing/registration/insurance; and
- Maneuverability and stability compromised due to small tires.
This government takes the safety of pedestrians and cyclists very seriously. The Ministry has undertaken many initiatives to improve the safety of vulnerable road users – mandatory bicycle helmets for children, stricter driver licensing for moped users, higher fines for failing to yield to pedestrians, and demerit points for school crossing violations. MTO partners with more than 100 community groups across the province, including police and municipalities, to promote road user and bicycle safety.
Despite these, and continuing efforts, Ontario’s Road Safety Annual Report (2006) indicates:
- Cyclist fatalities increased from 21 in 2005 to 32 in 2006, up 52.4% (total injuries decreased over the same period).
- Ontario’s cyclist fatality rate was 0.24 per 100,000 population (5.6% higher than the national average of 0.22).
- Pedestrian fatalities increased from 105 in 2005 to 126 in 2006, up 20% (total injuries increased slightly over the same period).
- Ontario’s pedestrian fatality rate was 0.99 per 100,000 population (up from 0.84 in 2005).
we will learn how to make your own Electric Bike Motor controller using Arduino, mc33151 Mosfet driver, and N-Channel IRF1404 Power Mosfets. After watching this video you will be able to design your own High Power Electric Bike motor controller. In this Tutorial, I am also going to explain why maximum motor drivers get fail. Watch my Video Tutorial in which I used the same Electric Bike Motor Controller, Smart Electric Bike.
Using only one Mosfet to control a motor is very easy, but when it comes to parallel MOSFETs the things really get complex. So today I am going to practically show you how to use MOSFETs in parallel to control a 24v 500Watt Electric Bike Moto
An electric motorcycle works essentially the same way a gas-powered motorcycle works it is propelled by an engine, and that engine requires fuel. The main difference is that the gas fuel in a conventional motorcycle is replaced by either batteries or fuel cells in an electric version. The operating principle of an electric motor is quite similar to that of a gas engine. In both cases motorcycles are powered by mechanical energy, but only in one case are they powered by rechargeable batteries. Electric vehicles run on electricity, that causes a pole into the motor to spin it. It isn’t so much a fuel-powered motor but rather a battery that can travel a range of 40 to 100 miles between charges .When the battery is ON the current flows to the motor and the power is transmitted to the rear wheels with the help of chain drive shaft
Benefits of the Project- Environmentally friendly
- Reduced commute times, fuel costs and emissions
- Increased mobility
- No insurance, licence or registration requirements
- Relatively inexpensive alternative mode of transportation
- Expand cycling opportunities for Ontarians who are not able to or are concerned about using conventional bicycles that are solely muscular-powered.
Battery ? Motor ? Controller ? Shaft drive ? Throttle ? Charger
As the future of automobiles will be mostly of electrical and electronics this would help in such way. While the market abounds in motorbikes, electric bikes will soon be the mode of communication for almost every household.Thus the cost of the fuel and the economical affects that are being faced can be reduced .Electric bike is quite eco friendly and itcan bring a huge development to the society in the future here in our project the charging is being the major drawback and the alternate source can be found and it will be rectified as soon as possible
a. Deployable batteries can be taken inside house b. Cost of the unit is very low. c. Easy to carry since it is portable. d. Less energy consumed. e. High efficiency can be obtained if inverter is used. f. If using solar panel, free utilization of energy can be done.
The implementation of the project depend upon the amount of time and resource todo the project in an effective manner. ? Alternate source for charging is to be found soon and it also may be implemented. ? Process of increasing the efficiency and power is to be improved and further steps will be taken
With the increasing consumption of natural resources of petrol, diesel it is necessary to shift our way towards alternate resources like the Electric bike and others because it is necessary to identify new way of transport. Electric bike is a modification of the existing cycle by using electric energy and also solar energy if solar panels are provided, that would sum up to increase in energy production. Since it is energy efficient, electric bike is cheaper and affordable to anyone. It can be used for shorter distances by people of any age. It can be contrived throughout the year. The most vital feature of the electric bike is that it does not consume fossil fuels thereby saving crores of foreign currencies. The second most important feature is it is pollution free, ecofriendly and noiseless in operation. For
Final Deliverable of the Project Hardware SystemCore Industry TransportationOther IndustriesCore Technology OthersOther TechnologiesSustainable Development Goals Decent Work and Economic GrowthRequired Resources| Item Name | Type | No. of Units | Per Unit Cost (in Rs) | Total (in Rs) |
|---|---|---|---|---|
| Total in (Rs) | 58250 | |||
| motor dc | Equipment | 1 | 20000 | 20000 |
| dry cell battery | Equipment | 1 | 25000 | 25000 |
| complete bike frame | Equipment | 1 | 10000 | 10000 |
| audrino | Equipment | 2 | 500 | 1000 |
| Boost Converter(XL-6009)) | Equipment | 1 | 200 | 200 |
| PCB board | Equipment | 3 | 150 | 450 |
| PCB design printing | Miscellaneous | 15 | 50 | 750 |
| Soldering Wire | Miscellaneous | 1 | 650 | 650 |
| Bread Board | Equipment | 1 | 200 | 200 |